OpenControls Logo

STIG Viewer

STIGViewer Support

The Nokia perimeter router must be configured to drop IPv6 packets that contain a Destination Option header with invalid option type values.

Overview

Finding IDVersionRule IDIA ControlsSeverity
V-283836NOKI-RT-000180SV-283836r1203757_ruleCCI-002403medium
Description
These options are intended to be for the Hop-by-Hop header only. The optional and extensible natures of the IPv6 extension headers require higher scrutiny since many implementations do not always drop packets with headers that can be recognized. This could cause a denial of service on the target device. In addition, the type, length, value (TLV) formatting provides the ability for headers to be very large.
STIGDate
Nokia Service Router OS 25.x Router Security Technical Implementation Guide2026-06-15

Related Frameworks

1 mapping across 3 frameworks
SCF0 mappings

No source states a mapping between these directly.

Also reachable in 3 hops (2) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

NET-03Boundary Protection
0.50
NET-04.1Deny Traffic by Default & Allow Traffic by Exception
0.50
NIST 800-530 mappings

No source states a mapping between these directly.

Also reachable in 2 hops (8) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

CM-6Configuration Settings
1.00
SC-24Fail in Known State
1.00
SC-47Alternate Communications Paths
1.00
SC-5Denial-of-service Protection
1.00
SC-7Boundary Protection
1.00
SC-7(11)Restrict Incoming Communications Traffic
1.00
SC-7(29)Separate Subnets to Isolate Functions
1.00
SC-7(5)Deny by Default — Allow by Exception
1.00
CCI1 mapping
CCI-002403
1.00

Details

Check Text (C-283836r1203757_chk)

This requirement is not applicable for the DODIN Backbone. Review the router configuration and determine if filters are bound to the external interfaces to drop IPv6 packets containing a Destination Option header with option type values of 0x05 (Router Alert) or 0xC2 (Jumbo Payload). Verify the IPv6 filter has the next header value set to 60, as shown in the example below: - show filter ipv6 40 Entry : 10 Description : (Not Specified) Log Id : n/a Src. IP : ::/0 Src. Port : n/a Dest. IP : ::/0 Dest. Port : n/a Next Header : 60 Verify an "Ing IPv6 Flt" has been applied to the interface, as shown in the example below: - show router interface "TO-PE2" detail | match "Ingr IPv6 Flt" Egr IPv6 Flt : none Ingr IPv6 Flt : 40 If the router is not configured to drop IPv6 packets containing a Destination Option header with invalid option type values, this is a finding.

Fix Text (F-88306r1203756_fix)

Configure the router to drop IPv6 packets containing a Destination Option header with option type values of 0x05 (Router Alert) or 0xC2 (Jumbo Payload). Configure an IPv6 filter to drop packets with a next-header value of 60 (value 60 corresponds to the Destination Option header). This will drop all packets with a Destination Option header. Configure an IPv6 filter: - config>filter# ipv6-filter 40 create - config>filter>ipv6-filter# entry 10 create - config>filter>ipv6-filter>entry# match next-header 60 - config>filter>ipv6-filter>entry>match# back - config>filter>ipv6-filter>entry# action drop - config>filter>ipv6-filter>entry# exit all Apply the IPv6 filter to the interface: - configure router interface "TO-PE2" ingress filter ipv6 40