STIGViewer Support

The Juniper out-of-band management (OOBM) gateway router must be configured to forward only authorized management traffic to the Network Operations Center (NOC).

Overview

Finding IDVersionRule IDIA ControlsSeverity
V-217045JUNI-RT-000400SV-217045r604135_ruleCCI-001097medium
Description
The OOBM network is an IP network used exclusively for the transport of OAM&P data from the network being managed to the OSS components located at the NOC. Its design provides connectivity to each managed network device, enabling network management traffic to flow between the managed network elements and the NOC. This allows the use of paths separate from those used by the managed network.
STIGDate
Juniper Router RTR Security Technical Implementation Guide2024-12-05

Related Frameworks

1 mapping across 5 frameworks
SCF0 mappings

No source states a mapping between these directly.

Also reachable in 3 hops (18) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

CFG-02Secure Baseline Configurations
1.00
CRY-01Use of Cryptographic Controls
1.00
CRY-01.1Alternate Physical Protection
1.00
CRY-03Transmission Confidentiality
1.00
CRY-04Transmission Integrity
1.00
CRY-05Encrypting Data At Rest
1.00
DCH-01Data Protection
1.00
IAC-21Least Privilege
1.00
MON-01Continuous Monitoring
1.00
MON-01.1Intrusion Detection & Prevention Systems (IDS & IPS)
1.00

+8 more (top 10 by confidence shown)

NIST 800-530 mappings

No source states a mapping between these directly.

Also reachable in 2 hops (10) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

CM-6Configuration Settings
1.00
SC-24Fail in Known State
1.00
SC-47Alternate Communications Paths
1.00
SC-5Denial-of-service Protection
1.00
SC-7Boundary Protection
1.00
SC-7(11)Restrict Incoming Communications Traffic
1.00
SC-7(29)Separate Subnets to Isolate Functions
1.00
SC-7(5)Deny by Default — Allow by Exception
1.00
SI-4System Monitoring
1.00
SI-4(11)Analyze Communications Traffic Anomalies
1.00
NIST 800-1710 mappings

No source states a mapping between these directly.

Also reachable in 3 hops (3) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

3.13.1
1.00
3.13.2
1.00
3.13.5
1.00
CCI1 mapping
NIST CSF 2.00 mappings

No source states a mapping between these directly.

Also reachable in 3 hops (5) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

Who does this work

15 NICE work roles and 9 EC-Council certifications.

This is an inference across published mappings, not a single claim by anyone. This check maps to a control, which maps to a Cybersecurity Framework outcome, which NIST assigns to the work roles below. EC-Council separately maps its certifications to those same roles.

A certification prepares someone for a role. It is not evidence that a holder is qualified, and neither NIST nor EC-Council has stated that any certification here addresses this check.

Work-role assignments published by NIST (NICE Framework Components 2.2.0 and the CSF 2.0 OLIR crosswalk). Certification mappings published by EC-Council.

Details

Check Text (C-217045r604135_chk)

This requirement is not applicable for the DoDIN Backbone. Review the network topology diagram to determine connectivity between the managed network and the NOC. Review the OOBM gateway router configuration to validate the path that the management traffic traverses. Verify that only management traffic is forwarded through the OOBM interface or IPsec tunnel. If an OOBM link is used, verify that the only authorized management traffic is transported to the NOC by reviewing the outbound filter applied to the OOBM interface as shown in the example below. interfaces { description "OOBM Net"; ge-1/1/0 { unit 0 { family inet { filter { output MGMT_TRAFFIC; } address 10.2.22.2/24; } } } … … … firewall { family inet { … … … filter MGMT_TRAFFIC { term ALLOW_SNMP { from { protocol udp; port [ snmp snmptrap ]; } then accept; } term ALLOW_TACACS { from { protocol tcp; port tacacs; } then accept; } term ALLOW_NETFLOW { from { protocol udp; port [ 2055 9995 9996 ]; } then accept; } term DENY_OTHER { then { syslog; discard; } } } } If an IPsec tunnel is used, verify that the only authorized management traffic is transported to the NOC by reviewing the filter referencing the applicable security association as shown int example below. firewall { family inet { … … … filter MGMT_TRAFFIC { term ALLOW_SNMP { from { protocol udp; port [ snmp snmptrap ]; } then ipsec-sa IPSEC_SA_MGMT; } term ALLOW_TACACS { from { protocol tcp; port tacacs; } then ipsec-sa IPSEC_SA_MGMT; } term ALLOW_NETFLOW { from { protocol udp; port [ 2055 9995 9996 ]; } then ipsec-sa IPSEC_SA_MGMT; } term OTHER { then accept; } } } If traffic other than authorized management traffic is permitted through the OOBM interface or IPsec tunnel, this is a finding.

Fix Text (F-18272r297004_fix)

This requirement is not applicable for the DoDIN Backbone. Configure filters to permit only authorized management traffic into IPsec tunnels or the OOBM interface used for forwarding management data as shown in the examples below. OOBM Link [edit firewall family inet] set filter MGMT_TRAFFIC term ALLOW_SNMP from protocol udp port [snmp snmptrap] set filter MGMT_TRAFFIC term ALLOW_SNMP then accept set filter MGMT_TRAFFIC term ALLOW_TACACS from protocol tcp port tacacs set filter MGMT_TRAFFIC term ALLOW_TACACS then accept set filter MGMT_TRAFFIC term ALLOW_NETFLOW from protocol udp port [2055 9995 9996] set filter MGMT_TRAFFIC term ALLOW_NETFLOW then accept set filter MGMT_TRAFFIC term DENY_OTHER then syslog discard [edit interfaces ge-1/1/0 unit 0 family inet] set filter output MGMT_TRAFFIC IPsec Tunnel [edit firewall family inet] set filter MGMT_TRAFFIC term ALLOW_SNMP from protocol udp port [snmp snmptrap] set filter MGMT_TRAFFIC term ALLOW_SNMP then ipsec-sa IPSEC_SA_MGMT set filter MGMT_TRAFFIC term ALLOW_TACACS from protocol tcp port tacacs set filter MGMT_TRAFFIC term ALLOW_TACACS then ipsec-sa IPSEC_SA_MGMT set filter MGMT_TRAFFIC term ALLOW_NETFLOW from protocol udp port [2055 9995 9996] set filter MGMT_TRAFFIC term ALLOW_NETFLOW then ipsec-sa IPSEC_SA_MGMT set filter MGMT_TRAFFIC term OTHER then accept