OpenControls Logo

STIG Viewer

STIGViewer Support

The Cisco ISE must configure the control plane to protect against or limit the effects of common types of Denial of Service (DoS) attacks on the device itself by configuring applicable system options and internet-options.

Overview

Finding IDVersionRule IDIA ControlsSeverity
V-242660CSCO-NM-000550SV-242660r1026050_ruleCCI-002385medium
Description
DoS is a condition when a resource is not available for legitimate users. When this occurs, the organization either cannot accomplish its mission or must operate at degraded capacity. This requirement addresses the configuration of network devices to mitigate the impact of DoS attacks that have occurred or are ongoing on device availability. For each network device, known and potential DoS attacks must be identified and solutions for each type implemented. A variety of technologies exist to limit or, in some cases, eliminate the effects of DoS attacks (e.g., limiting processes or restricting the number of sessions the device opens at one time). Employing increased capacity and bandwidth, combined with service redundancy, may reduce the susceptibility to some DoS attacks. The security safeguards cannot be defined at the DOD-level because they vary according to the capabilities of the individual network devices and the security controls applied on the adjacent networks (for example, firewalls performing packet filtering to block DoS attacks).
STIGDate
Cisco ISE NDM Security Technical Implementation Guide2026-06-03

Related Frameworks

1 mapping across 4 frameworks
SCF0 mappings

No source states a mapping between these directly.

Also reachable in 3 hops (13) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

MON-01Continuous Monitoring
1.00
MON-01.1Intrusion Detection & Prevention Systems (IDS & IPS)
1.00
MON-01.3Inbound & Outbound Communications Traffic
1.00
MON-01.4System Generated Alerts
1.00
MON-01.8Security Event Monitoring
1.00
NET-01Network Security Controls (NSC)
1.00
NET-02Layered Network Defenses
1.00
SEA-01Secure Engineering Principles
1.00
SEA-02Alignment With Enterprise Architecture
1.00
CAP-01Capacity & Performance Management
0.50

+3 more (top 10 by confidence shown)

NIST 800-530 mappings

No source states a mapping between these directly.

Also reachable in 2 hops (36) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

AC-10Concurrent Session Control
1.00
AC-17(9)Disconnect or Disable Access
1.00
AC-2(4)Automated Audit Actions
1.00
AC-3Access Enforcement
1.00
AC-4Information Flow Enforcement
1.00
AC-6(9)Log Use of Privileged Functions
1.00
AU-12Audit Record Generation
1.00
AU-3Content of Audit Records
1.00
AU-5Response to Audit Logging Process Failures
1.00
CM-11(2)Software Installation with Privileged Status
1.00

+26 more (top 10 by confidence shown)

CCI1 mapping
CCI-002385
1.00
NIST CSF 2.00 mappings

No source states a mapping between these directly.

Also reachable in 3 hops (3) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

DE.CM-01
1.00
PR.IR-01
1.00
PR.IR-04
0.50

Who does this work

12 NICE work roles and 9 EC-Council certifications.

This is an inference across published mappings, not a single claim by anyone. This check maps to a control, which maps to a Cybersecurity Framework outcome, which NIST assigns to the work roles below. EC-Council separately maps its certifications to those same roles.

A certification prepares someone for a role. It is not evidence that a holder is qualified, and neither NIST nor EC-Council has stated that any certification here addresses this check.

Work-role assignments published by NIST (NICE Framework Components 2.2.0 and the CSF 2.0 OLIR crosswalk). Certification mappings published by EC-Council.

Details

Check Text (C-242660r1026050_chk)

Verify the system and system-options are configured to protect against denial-of-service (DoS) attacks. (config)# do sh run | in syn (config)#do show run | in rate-limit If the system and system-options that limit the effects of common types of DoS attacks are not configured in compliance with the SSP, this is a finding.

Fix Text (F-45892r714289_fix)

Configure the system and system-options to protect against DoS attacks. These are examples of setting that should be adjusted to limit DoS attacks. The exact values will vary based on site traffic. Use the synflood-limit to configure a TCP SYN packet rate limit. To configure the limit of TCP/UDP/ICMP packets from a source IP address, use the rate-limit command in configuration mode.