OpenControls Logo

STIG Viewer

STIGViewer Support

For accounts using password authentication, the Cisco ISE must use FIPS-validated SHA-2 or later protocol to protect the integrity of the password authentication process.

Overview

Finding IDVersionRule IDIA ControlsSeverity
V-242651CSCO-NM-000460SV-242651r961029_ruleCCI-000197high
Description
Passwords need to be protected at all times, and encryption is the standard method for protecting passwords. If passwords are not encrypted, they can be plainly read (i.e., clear text) and easily compromised. The information system must specify the hash algorithm used for authenticating passwords. Implementation of this requirement requires configuration of FIPS-approved cipher block algorithm and block cipher modes for encryption. Note: Although allowed by SP800-131Ar1 for some applications, SHA-1 is considered a compromised hashing standard and is being phased out of use by industry and government standards. Unless required for legacy use, DOD systems should not be configured to use SHA-1 for integrity of remote access sessions. This requirement applies to all accounts, including authentication server, AAA, and local accounts such as the root account and the account of last resort.
STIGDate
Cisco ISE NDM Security Technical Implementation Guide2026-06-03

Related Frameworks

1 mapping across 4 frameworks
SCF0 mappings

No source states a mapping between these directly.

Also reachable in 3 hops (3) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

IAC-10Authenticator Management
0.50
IAC-10.1Password-Based Authentication
0.50
IAC-10.4Automated Support For Password Strength
0.50
NIST 800-530 mappings

No source states a mapping between these directly.

Also reachable in 2 hops (58) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

AC-17(1)Monitoring and Control
1.00
AC-17(2)Protection of Confidentiality and Integrity Using Encryption
1.00
AC-2(1)Automated System Account Management
1.00
AC-2(10)Shared and Group Account Credential Change
1.00
AC-2(11)Usage Conditions
1.00
AC-2(2)Automated Temporary and Emergency Account Management
1.00
AC-2(3)Disable Accounts
1.00
AC-2(4)Automated Audit Actions
1.00
AC-3Access Enforcement
1.00
AC-4Information Flow Enforcement
1.00

+48 more (top 10 by confidence shown)

NIST 800-1710 mappings

No source states a mapping between these directly.

Also reachable in 3 hops (4) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

3.5.10
1.00
3.5.7
1.00
3.5.8
1.00
3.5.9
1.00
CCI1 mapping
CCI-000197
1.00

Details

Check Text (C-242651r961029_chk)

Navigate to Administration >> System >> Settings >> FIPS Mode. Verify FIPS Mode is enabled. If FIPS Mode is enabled, this is not a finding. If FIPS mode is not configured, but the Cisco ISE is configured using an alternative manual method to configure the password authentication process to use a FIPS 140-2/140-3 validated SHA-2 (or greater), this can be lowered to a CAT 2 finding.

Fix Text (F-45883r916317_fix)

Enable FIPS Mode in Cisco ISE to ensure FIPS 140-2/140-3 algorithms are used in all security functions requiring cryptographic functions. 1. Choose Administration >> System >> Settings >> FIPS Mode. 2. Choose the "Enabled" option from the FIPS Mode drop-down list. 3. Click "Save" and restart the node. Note: Configuring FIPS mode is the required DOD configuration. However, this requirement can be lowered to a CAT 2 if the alternative manual configuration is used to configure the password authentication process to use a FIPS 140-2/140-3 validated SHA-2 (or greater).