OpenControls Logo

STIG Viewer

STIGViewer Support

The Cisco multicast Rendezvous Point (RP) switch must be configured to limit the multicast forwarding cache so that its resources are not saturated by managing an overwhelming number of Protocol Independent Multicast (PIM) and Multicast Source Discovery Protocol (MSDP) source-active entries.

Overview

Finding IDVersionRule IDIA ControlsSeverity
V-221056CISC-RT-000820SV-221056r863379_ruleCCI-002385low
Description
MSDP peering between networks enables sharing of multicast source information. Enclaves with an existing multicast topology using PIM-SM can configure their RP switches to peer with MSDP switches. As a first step of defense against a denial-of-service (DoS) attack, all RP switches must limit the multicast forwarding cache to ensure that switch resources are not saturated managing an overwhelming number of PIM and MSDP source-active entries.
STIGDate
Cisco IOS XE Switch RTR Security Technical Implementation Guide2026-03-04

Related Frameworks

1 mapping across 4 frameworks
SCF0 mappings

No source states a mapping between these directly.

Also reachable in 3 hops (13) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

MON-01Continuous Monitoring
1.00
MON-01.1Intrusion Detection & Prevention Systems (IDS & IPS)
1.00
MON-01.3Inbound & Outbound Communications Traffic
1.00
MON-01.4System Generated Alerts
1.00
MON-01.8Security Event Monitoring
1.00
NET-01Network Security Controls (NSC)
1.00
NET-02Layered Network Defenses
1.00
SEA-01Secure Engineering Principles
1.00
SEA-02Alignment With Enterprise Architecture
1.00
CAP-01Capacity & Performance Management
0.50

+3 more (top 10 by confidence shown)

NIST 800-530 mappings

No source states a mapping between these directly.

Also reachable in 2 hops (36) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

AC-10Concurrent Session Control
1.00
AC-17(9)Disconnect or Disable Access
1.00
AC-2(4)Automated Audit Actions
1.00
AC-3Access Enforcement
1.00
AC-4Information Flow Enforcement
1.00
AC-6(9)Log Use of Privileged Functions
1.00
AU-12Audit Record Generation
1.00
AU-3Content of Audit Records
1.00
AU-5Response to Audit Logging Process Failures
1.00
CM-11(2)Software Installation with Privileged Status
1.00

+26 more (top 10 by confidence shown)

CCI1 mapping
CCI-002385
1.00
NIST CSF 2.00 mappings

No source states a mapping between these directly.

Also reachable in 3 hops (3) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

DE.CM-01
1.00
PR.IR-01
1.00
PR.IR-04
0.50

Who does this work

12 NICE work roles and 9 EC-Council certifications.

This is an inference across published mappings, not a single claim by anyone. This check maps to a control, which maps to a Cybersecurity Framework outcome, which NIST assigns to the work roles below. EC-Council separately maps its certifications to those same roles.

A certification prepares someone for a role. It is not evidence that a holder is qualified, and neither NIST nor EC-Council has stated that any certification here addresses this check.

Work-role assignments published by NIST (NICE Framework Components 2.2.0 and the CSF 2.0 OLIR crosswalk). Certification mappings published by EC-Council.

Details

Check Text (C-221056r863379_chk)

The Cisco switch does not have a mechanism to limit the multicast forwarding cache. However, the risk associated with this requirement can be fully mitigated by configuring the switch to: 1. Filter PIM register messages. 2. Rate limiting the number of PIM register messages. 3. Accept MSDP packets only from known MSDP peers. Step 1: Verify that the RP is configured to filter PIM register messages for any undesirable multicast groups and sources. The example below will deny any multicast streams for groups 239.5.0.0/16 and allow from only sources x.1.2.6 and x.1.2.7. ip pim rp-address 10.1.12.3 ip pim accept-register list PIM_REGISTER_FILTER … … … ip access-list extended PIM_REGISTER_FILTER deny ip any 239.5.0.0 0.0.255.255 permit ip host x.1.2.6 any permit ip host x.1.2.7 any deny ip any any Step 2: Verify that the RP is configured to rate limiting the number of PIM register messages as shown in the example below: ip pim rp-address 10.2.2.2 ip pim register-rate-limit nn Step 3: Review the switch configuration to determine if there is a receive path or interface filter to only accept MSDP packets from known MSDP peers as shown in the example below: Step 3a: Verify that interfaces used for MSDP peering have an inbound ACL as shown in the example. interface GigabitEthernet1/1 ip address x.1.28.8 255.255.255.0 ip access-group EXTERNAL_ACL_INBOUND in ip pim sparse-mode Step 3b: Verify that the ACL restricts MSDP peering to only known sources. ip access-list extended EXTERNAL_ACL_INBOUND permit tcp any any established permit tcp host x.1.28.2 host x.1.28.8 eq 639 deny tcp any host x.1.28.8 eq 639 log permit tcp host x.1.28.2 host 10.1.28.8 eq bgp permit tcp host x.1.28.2 eq bgp host x.1.28.8 permit pim host x.1.28.2 pim host x.1.28.8 … … … deny ip any any log Note: MSDP connections is via TCP port 639. If the RP switch is not configured to filter PIM register messages, rate limiting the number of PIM register messages, and accept MSDP packets only from known MSDP peers, this is a finding.

Fix Text (F-22760r507601_fix)

The risk associated with this requirement can be fully mitigated by configuring the switch to filter PIM register messages, rate limiting the number of PIM register messages, and accept MSDP packets only from known MSDP peers. Step 1: Configure the switch to filter PIM register messages received from a multicast DR for any undesirable multicast groups and sources. The example below will deny any multicast streams for groups 239.5.0.0/16 and allow from only sources x.1.2.6 and x.1.2.7. SW1(config)#ip access-list extended PIM_REGISTER_FILTER SW1(config-ext-nacl)#deny ip any 239.5.0.0 0.0.255.255 SW1(config-ext-nacl)#permit ip host x.1.2.6 any SW1(config-ext-nacl)#permit ip host x.1.2.7 any SW1(config-ext-nacl)#deny ip any any SW1(config-ext-nacl)#exit SW1(config)#ip pim accept-register list PIM_REGISTER_FILTER SW1(config)#end Step 2: Configure the RP to rate limit the number of multicast register messages. SW1(config)#ip pim register-rate-limit nn Step 3: Configure the receive path or interface ACLs to only accept MSDP packets from known MSDP peers. SW1(config)#ip access-list extended EXTERNAL_ACL_INBOUND SW1(config-ext-nacl)#permit tcp any any established SW1(config-ext-nacl)#permit tcp host x.1.28.2 host x.1.28.8 eq 639 SW1(config-ext-nacl)#deny tcp any host x.1.28.8 eq 639 SW1(config-ext-nacl)#permit tcp host x.1.28.2 host x.1.28.8 eq bgp SW1(config-ext-nacl)#permit tcp host x.1.28.2 eq bgp host x.1.28.8 SW1(config-ext-nacl)#permit pim host x.1.28.2 host x.1.28.8 … … … SW1(config-ext-nacl)#deny ip any any