OpenControls Logo

STIG Viewer

STIGViewer Support

The multicast rendezvous point (RP) must be configured to rate limit the number of Protocol Independent Multicast (PIM) Register messages.

Overview

Finding IDVersionRule IDIA ControlsSeverity
V-272091CACI-RT-000031SV-272091r1168160_ruleCCI-002385medium
Description
When a new source starts transmitting in a PIM Sparse Mode network, the designated router (DR) will encapsulate the multicast packets into register messages and forward them to the RP using unicast. This process can be taxing on the CPU for both the DR and the RP if the source is running at a high data rate and there are many new sources starting at the same time. This scenario can potentially occur immediately after a network failover. The rate limit for the number of register messages should be set to a relatively low value based on the known number of multicast sources within the multicast domain. Satisfies: SRG-NET-000362-RTR-000120
STIGDate
Cisco ACI Router Security Technical Implementation Guide2025-12-11

Related Frameworks

1 mapping across 4 frameworks
SCF0 mappings

No source states a mapping between these directly.

Also reachable in 3 hops (13) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

MON-01Continuous Monitoring
1.00
MON-01.1Intrusion Detection & Prevention Systems (IDS & IPS)
1.00
MON-01.3Inbound & Outbound Communications Traffic
1.00
MON-01.4System Generated Alerts
1.00
MON-01.8Security Event Monitoring
1.00
NET-01Network Security Controls (NSC)
1.00
NET-02Layered Network Defenses
1.00
SEA-01Secure Engineering Principles
1.00
SEA-02Alignment With Enterprise Architecture
1.00
CAP-01Capacity & Performance Management
0.50

+3 more (top 10 by confidence shown)

NIST 800-530 mappings

No source states a mapping between these directly.

Also reachable in 2 hops (36) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

AC-10Concurrent Session Control
1.00
AC-17(9)Disconnect or Disable Access
1.00
AC-2(4)Automated Audit Actions
1.00
AC-3Access Enforcement
1.00
AC-4Information Flow Enforcement
1.00
AC-6(9)Log Use of Privileged Functions
1.00
AU-12Audit Record Generation
1.00
AU-3Content of Audit Records
1.00
AU-5Response to Audit Logging Process Failures
1.00
CM-11(2)Software Installation with Privileged Status
1.00

+26 more (top 10 by confidence shown)

CCI1 mapping
CCI-002385
1.00
NIST CSF 2.00 mappings

No source states a mapping between these directly.

Also reachable in 3 hops (3) derived by us, not asserted by any source

Each of these is a route we composed by chaining published mappings. No publisher states a relationship between the two endpoints.

DE.CM-01
1.00
PR.IR-01
1.00
PR.IR-04
0.50

Who does this work

12 NICE work roles and 9 EC-Council certifications.

This is an inference across published mappings, not a single claim by anyone. This check maps to a control, which maps to a Cybersecurity Framework outcome, which NIST assigns to the work roles below. EC-Council separately maps its certifications to those same roles.

A certification prepares someone for a role. It is not evidence that a holder is qualified, and neither NIST nor EC-Council has stated that any certification here addresses this check.

Work-role assignments published by NIST (NICE Framework Components 2.2.0 and the CSF 2.0 OLIR crosswalk). Certification mappings published by EC-Council.

Details

Check Text (C-272091r1168160_chk)

Review the PIM configuration: Tenants >> {{your_Tenant}} >> Networking >> VRF >> {{your_VRF}} >> Multicast >> Configuration >> Pattern Policy >> under Register Traffic Policy look for Max Rate (packets per second) If the RP router is not configured to filter PIM register messages, rate limit the number of PIM register messages, and accept multicast packets only from known peers, this is a finding.

Fix Text (F-76048r1168159_fix)

Configure the switch to filter PIM register messages, rate limit the number of PIM register messages, and accept multicast packets only from known peers. Use the command "ip pim register-rate-limit <rate>", where <rate> specifies the desired maximum number of register messages per second allowed to be sent. Navigate to the following location to configure: Tenants >> {{your_Tenant}} >> Networking >> VRF >> {{your_VRF}} >> Multicast >> Configuration >> Pattern Policy >> under Register Traffic Policy look for Max Rate (packets per second)