The Cisco router providing connectivity to the Network Operations Center (NOC) must be configured to forward all in-band management traffic via an IPsec tunnel.

Overview

Finding ID	Version	Rule ID	IA Controls	Severity
V-96589	CISC-RT-000460	SV-105727r1_rule		Medium

Description
When the production network is managed in-band, the management network could be housed at a NOC that is located remotely at single or multiple interconnected sites. NOC interconnectivity, as well as connectivity between the NOC and the managed network, must be enabled using IPsec tunnels to provide the separation and integrity of the managed traffic.

STIG	Date
Cisco IOS Router RTR Security Technical Implementation Guide	2020-06-30

Details

Check Text ( C-95425r1_chk )
This requirement is not applicable for the DODIN Backbone. Verify that all traffic from the managed network to the management network or NOC and vice-versa is secured via IPsec tunnel. Step 1: Note the crypto map applied to the external interface. interface GigabitEthernet0/2 description link to DISN ip address x.1.24.4 255.255.255.0 crypto map IPSEC_MGMT_MAP Step 2: Review the ISAKMP policy for Phase 1 negotiations and Phase 2 policy for data encryption. crypto isakmp policy 10 authentication pre-share hash sha256 crypto isakmp key xxxxxx address x.1.12.1 ! ! crypto ipsec transform-set TRANS_SET ah-sha256-hmac esp-aes Step 3: Review the crypto map that was bound to the external interface and note the ACL defined that identifies the interesting traffic for the IPsec tunnel. crypto map IPSEC_MGMT_MAP 10 ipsec-isakmp set peer x.1.12.1 set transform-set TRANS_SET match address MGMT_TRAFFIC_ACL Step 4: Review the ACL defined in the crypto map and verify that the destination is the management network. ip access-list extended MGMT_TRAFFIC_ACL permit ip 10.1.34.0 0.0.0.255 10.22.2.0 0.0.0.255 Note: The management network is this example is 10.22.2.0/24 If the management traffic is not secured via IPsec tunnel, this is a finding.

Check Text ( C-95425r1_chk )

This requirement is not applicable for the DODIN Backbone.

Verify that all traffic from the managed network to the management network or NOC and vice-versa is secured via IPsec tunnel.

Step 1: Note the crypto map applied to the external interface.

interface GigabitEthernet0/2
description link to DISN
ip address x.1.24.4 255.255.255.0
crypto map IPSEC_MGMT_MAP

Step 2: Review the ISAKMP policy for Phase 1 negotiations and Phase 2 policy for data encryption.

crypto isakmp policy 10
authentication pre-share
hash sha256
crypto isakmp key xxxxxx address x.1.12.1
!
!
crypto ipsec transform-set TRANS_SET ah-sha256-hmac esp-aes

Step 3: Review the crypto map that was bound to the external interface and note the ACL defined that identifies the interesting traffic for the IPsec tunnel.

crypto map IPSEC_MGMT_MAP 10 ipsec-isakmp
set peer x.1.12.1
set transform-set TRANS_SET
match address MGMT_TRAFFIC_ACL

Step 4: Review the ACL defined in the crypto map and verify that the destination is the management network.

ip access-list extended MGMT_TRAFFIC_ACL
permit ip 10.1.34.0 0.0.0.255 10.22.2.0 0.0.0.255

Note: The management network is this example is 10.22.2.0/24

If the management traffic is not secured via IPsec tunnel, this is a finding.

Fix Text (F-102263r1_fix)
This requirement is not applicable for the DODIN Backbone. Ensure that all traffic from the managed network to the management network is secured via IPsec tunnel as shown in the configuration examples below. Step 1: Configure the ACL for the management network as the destination. This ACL will be defined in the crypto as the interesting traffic to be forwarded into the IPsec tunnel. R4(config)#ip access-list extended MGMT_TRAFFIC_ACL R4(config-ext-nacl)#permit ip 10.1.34.0 0.0.0.255 10.22.2.0 0.0.0.255 R4(config-ext-nacl)#exit Step 2: Create an ISAKMP policy for Phase 1 negotiations R4(config)#crypto isakmp policy 10 R4(config-isakmp)#hash sha256 R4(config-isakmp)#authentication pre-share R4(config-isakmp)#exit Step 3: Specify the pre-shared key and the remote peer address R4(config)#crypto isakmp key 0 xxxxxx address 10.1.12.1 Note: Digital certificates can be utilized as an alternative. Step 4: Create the Phase 2 policy for the data encryption R4(config)#crypto ipsec transform-set TRANS_SET ah-sha256-hmac esp-aes R4(cfg-crypto-trans)#mode tunnel R4(cfg-crypto-trans)#exit Step 5: Create the crypto map R4(config)#crypto map IPSEC_MGMT_MAP 10 ipsec-isakmp R4(config-crypto-map)#set peer 10.1.12.1 R4(config-crypto-map)#match address MGMT_TRAFFIC_ACL R4(config-crypto-map)#set transform-set TRANS_SET R4(config-crypto-map)#end Step 6: Apply the crypto map to the external interface R4(config)#int g0/2 R4(config-if)#crypto map IPSEC_MGMT_MAP

Fix Text (F-102263r1_fix)

This requirement is not applicable for the DODIN Backbone.

Ensure that all traffic from the managed network to the management network is secured via IPsec tunnel as shown in the configuration examples below.

Step 1: Configure the ACL for the management network as the destination. This ACL will be defined in the crypto as the interesting traffic to be forwarded into the IPsec tunnel.

R4(config)#ip access-list extended MGMT_TRAFFIC_ACL
R4(config-ext-nacl)#permit ip 10.1.34.0 0.0.0.255 10.22.2.0 0.0.0.255
R4(config-ext-nacl)#exit

Step 2: Create an ISAKMP policy for Phase 1 negotiations

R4(config)#crypto isakmp policy 10
R4(config-isakmp)#hash sha256
R4(config-isakmp)#authentication pre-share
R4(config-isakmp)#exit

Step 3: Specify the pre-shared key and the remote peer address

R4(config)#crypto isakmp key 0 xxxxxx address 10.1.12.1

Note: Digital certificates can be utilized as an alternative.

Step 4: Create the Phase 2 policy for the data encryption

R4(config)#crypto ipsec transform-set TRANS_SET ah-sha256-hmac esp-aes
R4(cfg-crypto-trans)#mode tunnel
R4(cfg-crypto-trans)#exit

Step 5: Create the crypto map

R4(config)#crypto map IPSEC_MGMT_MAP 10 ipsec-isakmp
R4(config-crypto-map)#set peer 10.1.12.1
R4(config-crypto-map)#match address MGMT_TRAFFIC_ACL
R4(config-crypto-map)#set transform-set TRANS_SET
R4(config-crypto-map)#end

Step 6: Apply the crypto map to the external interface
R4(config)#int g0/2
R4(config-if)#crypto map IPSEC_MGMT_MAP